The POWER TIG 1640 DC HF is a DC TIG/MMA welding power source, inverter technology. In TIG mode the arc is started either in HF or with the Cebora lift system. It features a 2 stage/4 stage selection key, while the remote control device allows to connect a foot control or, alternatively, to work with a torch fitted with an up/down control.
The welding current can be adjusted from 5 to 160 A and two potentiometers allow respectively the slope down and the post-gas function adjustment. This power source represents the entry level model in the complete range of Cebora DC TIG welding power sources and is mainly intended for maintenance and repair work, as well as for small productions.
The compliance with EN 61000-3-12 brings substantial energy saving and a wide supply voltage tolerance (+15% / -20%). The power source can be powered by motor generators of adequate power (Min. 6 KVA).
= standard = optional
Feature | Power source part number | ||||||
---|---|---|---|---|---|---|---|
264 | 265 |
360 362 |
364 | 365 |
363 373 |
369 370 371 |
|
Max. pulse frequency 2.5 kHz |
|||||||
Max. pulse frequency 500 Hz | |||||||
High Frequency ignition |
|||||||
"Lift by Cebora" ignition | |||||||
Spot welding mode |
|||||||
2 times / 4 times | |||||||
3 level mode | |||||||
2 level and 4 time mode | |||||||
Minimum current in AC TIG 5 A | n.a. | n.a. | n.a. | n.a. | |||
Max. AC frequency 150 Hz |
n.a. | n.a. | n.a. | n.a. | |||
Crater current adjustment | |||||||
Wave form selection | n.a. | n.a. | n.a. | n.a. | |||
AC horizontal balance | n.a. | n.a. | n.a. | n.a. | |||
AC vertical balance (AAd) |
n.a. | n.a. | n.a. | n.a. | |||
Remote control |
|||||||
Synergic parameters |
|||||||
Slope up adjustment | |||||||
Slope down adjustment | |||||||
Pre-gas adjustment | |||||||
Post-gas adjustment | |||||||
Load controlled fan | |||||||
Job mode | |||||||
Interface for cooling unit | |||||||
Ready for automatic Plasma Welding console | |||||||
Ready for manual Plasma Welding console | |||||||
Interface for TIG Hot / Cold Wire feeder | |||||||
Ready for interfacing with robot via either analog or fieldbus | |||||||
TIG MIX process | n.a. | n.a. | n.a. | n.a. | |||
EVO Start (ESt) adjustment | |||||||
HF ignition by "EVO Lift" (ELF) | |||||||
Panel locking | |||||||
Digital gas control | |||||||
Quality Control function | |||||||
DC MMA welding | |||||||
AC MMA welding | n.a. | ||||||
"Arc Force" function in MMA welding | |||||||
"Hot Start" current | |||||||
USB interface | |||||||
RS-232 interface | |||||||
Possibility to update the software | |||||||
Conformity with EN61000-3-12 (PFC) | |||||||
Suitable for use in environments with increased hazard of electric shock | |||||||
IP23S protection class | |||||||
The power source can be powered by motor generators of adequate power | |||||||
Single phase power supply 230V +15% / -20% | |||||||
Three-phase power supply 400V ±10% | |||||||
Multivoltage single phase power supply 115 - 230V +15% / -20% | |||||||
Multivoltage three-phase power supply 208-220-230-400-440V ±10% |
Art. | 264 | Specifications | ||
---|---|---|---|---|
TIG |
MMA |
|||
230V 50/60 Hz |
Single phase input |
|||
16 A |
Fuse rating (slow blow) |
|||
3,4 KVA 40% |
4,6 KVA 30% |
Input power |
||
5A ÷ 160A |
10A ÷ 140A |
Current adjustment range |
||
160A 40% 110A 100% |
140A 30% 95A 100% |
Duty Cycle (10 min.40°C) |
||
IP 23 S |
Protection class |
|||
10,3 Kg |
Weight |
|||
171x420x340H |
Dimensions mm |